Chart
Best Wood for Pyrography: 12 Species Compared in One Chart
Published Updated
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Basswood is the best wood for pyrography for most projects: pale, soft at 410 lbf Janka, with a fine, even grain, so a burn shows clearly at low to medium heat. Aspen, butternut, poplar, birch and maple also burn well. Pine, cedar and oak burn unevenly because of their grain, and walnut and cherry are dark, so the burn has less contrast.
Gear for this job
All 7 picks comparedFoggy Bottom basswood plaques, 10 x 8 in, 5-pack
See price on AmazonSee it on AmazonWilson Basswood Round Wood Slices, 4 Pack
See price on AmazonSee it on AmazonMineIdea Unfinished Gothic Arch Wood Plaques, 12
See price on AmazonSee it on Amazon

Three things decide how a board takes a burn: color, hardness and grain. Pale wood gives the mark contrast. Soft wood marks at lower heat, while hard wood needs more. Even grain lets the tip travel at one speed, and wood with soft and hard bands burns in stripes. The chart lists the 12 species people ask about most. Hardness figures come from The Wood Database and the standard Janka table. The heat bands are this site's general guide, because no pen maker publishes a setting per species.
Pyrography wood chart: 12 species compared
Read across a row. The lower the Janka number, the softer the wood and the lower the heat band a line starts in. The burn column describes the wood as references describe it. It is not a test result. For the ranges in degrees and a lookup by pen type, use the wood burning temperature chart.
| Wood | Janka (lbf) | Color and grain | How it burns | Heat band for lines |
|---|---|---|---|---|
| Basswood | 410 | Pale white to light brown, fine even grain | The standard choice: an even surface, clear contrast | Low to medium |
| Aspen | 350 | Pale yellow to nearly white, uniform | Very soft, so a hot tip sinks in | Low to medium |
| Butternut | 490 | Light tan, coarser texture, visible rings | Like basswood, with a coarser surface | Low to medium |
| Yellow poplar | 540 | Pale cream with green or grey streaks | The streaks show through the design | Medium |
| Birch | 910 (paper), 1,260 (yellow) | Pale, fine texture. The usual plywood face | Pale and fine, but needs more heat than basswood | Medium to high |
| Soft maple | 950 | Pale, fine even texture | Pale and fine, good contrast | Medium to high |
| Hard maple | 1,450 | Pale, dense, fine even texture | Crisp lines, but slow going | High |
| Cherry | 950 | Reddish brown, fine grain | Less contrast on the reddish wood | Medium to high |
| Walnut | 1,010 | Dark brown | Low contrast on the dark wood | Medium to high |
| Pine (eastern white) | 380 | Pale, with soft and hard bands, resin | Uneven: the bands burn differently | Low to medium |
| Cedar (western red) | 350 | Reddish brown, soft, strong grain | Uneven | Low |
| Oak | 1,220 to 1,290 (red), 1,360 (white) | Light brown, coarse, open pores | Uneven: open pores break up lines | High |
How to read the chart: Janka hardness and heat bands for the pen
Janka hardness is the force needed to press a steel ball halfway into the wood, given in pounds-force (lbf). It matters here because of one rule from the burner maker Colwood: set a higher number for harder wood and a lower number for softer wood. The chart turns that rule into bands. Under 500 lbf a line starts in low to medium, from 500 to 900 in medium, from 900 to 1,100 in medium to high, and above 1,100 in high. Cedar is set to low because its grain is so soft.
A band is a range, not a setting. Craft pens are not calibrated, and a dial number or color zone is not a temperature. Take an offcut of the same wood, sanded the same way, start at the bottom of the band and raise the heat until a steady stroke leaves an even toast-brown line. Shading runs about one band cooler than lines and is built up in passes: see how to shade pyrography.
- Low: 400 to 550 F (200 to 290 C). Pale tan to light brown on pale wood.
- Medium: 550 to 750 F (290 to 400 C). Mid toast brown, the general starting point for lines.
- High: 750 to 950 F (400 to 510 C). Dark brown to near black.
- Very high: above 950 F (510 C). Black, and it cuts into the surface. Wire-nib burners only, and not needed for ordinary flat work.
Is basswood good for pyrography?
Yes. Basswood is the standard choice, and the reasons are all in its row. At 410 lbf it is soft, so a line appears at low to medium heat. The Wood Database describes it as pale white to light brown, with straight grain, a fine, even texture and growth rings that barely show. Nothing in the surface competes with the design.
It is also the easiest pyrography wood to buy ready to burn: bark-edged rounds, routed plaques and thin plywood sheets are all sold in basswood. Aspen is paler and softer still at 350 lbf, which means a hot tip sinks in. Butternut, at 490 lbf, is light tan with a coarser texture and more visible rings. Both start in the same band as basswood.
Is pine or cedar good for pyrography?
No, not for even work. Colwood's hints page says it flatly: cedar and pine are unsatisfactory to burn because of their grain. Eastern white pine is soft overall at 380 lbf, but each growth ring has a soft band and a hard band, and the two burn differently. One stroke at one speed comes out light and dark in stripes. The Wood Database also notes numerous resin canals in the wood.
Western red cedar is just as soft at 350 lbf. It is reddish brown with a coarse texture and a strong grain, so it has both problems at once: an uneven burn and less contrast. If pine or cedar is the board you already own, it will take a mark. Keep to the low end of its band, choose a bold design over fine shading, and expect the grain to show through.
Is oak good for pyrography?
Only for bold designs. Oak is hard, 1,220 to 1,290 lbf for red oak and 1,360 lbf for white oak, so lines start in the high band. Hardness is not the real problem, though. The Wood Database describes red oak as coarse and uneven in texture, with large open pores. Those pores break up a fine line.
For a hard wood that still takes a clean line, hard maple is the better pick. It is harder than oak at 1,450 lbf, but it is pale with a fine, even texture, and lines come out crisp. The cost is speed: it needs the high band and patience. Soft maple at 950 lbf and birch give a similar pale surface in the medium to high band.
Walnut and cherry: dark woods under a pyrography pen
Both start in the medium to high band, and both have a contrast problem, not a heat problem. A burn is brown. Walnut runs from pale brown to dark chocolate brown, so a brown line has little to stand out against. Cherry starts lighter, a pinkish brown, but The Wood Database notes that it darkens to a medium reddish brown with time and exposure to light. On either wood, plan for dark, bold lines. Pale shading is the first thing to get lost.
Rounds, plaques or plywood: where each pyrography wood turns up
Species is half the choice. The other half is the form the wood comes in, which decides how much sanding it needs and what lies under the surface. Whatever the form, sand with the grain to 220 to 320 grit and wipe off the dust.
Burn only bare, untreated wood: never pressure-treated, painted, stained or varnished wood, MDF or particle board. Plywood and bamboo have rules of their own. See wood burning on plywood, wood burning on bamboo and burning on finished wood.
| Wood | Where you meet it | Watch for |
|---|---|---|
| Basswood | Bark-edged rounds, routed plaques, thin plywood sheets | Rounds may be sanded on one side only |
| Birch | The usual face veneer of craft plywood | Burn the face veneer only, never down into the glue |
| Pine | Ornament slices, trim boards | Resin and hard bands: an uneven burn |
| Yellow poplar | Boards for painted trim, plywood | Green or grey streaks under the design |
| Hard maple | Cutting boards and butcher blocks | Sand off any factory oil or finish first |
| Oak, walnut, cherry | Furniture lumber and veneer | Open pores on oak, low contrast on walnut and cherry |
Choosing a blank you plan to paint as well as burn
If a piece will get both burning and paint, the wood matters beyond how it burns. Smooth, evenly grained species take paint more evenly, while open or resinous grain can show through a thin coat and may need extra preparation before color goes on.
Many craft blanks arrive with a factory finish, which burns poorly and can also repel paint. Check whether the surface is bare before you buy more than one, and sand a test patch if you are unsure. Preparation differs for bare wood and for wood that has been painted before, so follow the steps for your case before you start.
Quick answers
Short answers to the wood questions. Hardness figures are Janka values in pounds-force. Heat bands are a general guide to confirm on scrap.
- What is the best wood for pyrography? Basswood. It is pale, soft at 410 lbf and fine-grained, and it is sold as rounds, plaques and plywood sheets.
- Is basswood good for pyrography? Yes. It is the standard choice. Lines start in the low to medium band.
- Is pine good for pyrography? Not for even work. Its soft and hard bands burn differently, and Colwood rates pine unsatisfactory.
- Is oak good for pyrography? Only for bold designs. Open pores break up fine lines, and it needs the high band.
- Does pyrography on cedar work? It takes a mark, but unevenly. Use the low band and expect the strong grain to show.
Use this chart
Print it, save the image version, or put it on your own site or forum post with the code below. The code keeps a link back to this page as the source.
Embed code
<a href="https://burnandgrain.com/blog/wood-for-pyrography"><img src="https://burnandgrain.com/charts/wood-for-pyrography/image.png" alt="Best Wood for Pyrography: 12 Species Compared in One Chart" width="600" loading="lazy"></a> <p>Source: <a href="https://burnandgrain.com/blog/wood-for-pyrography">Best Wood for Pyrography: 12 Species Compared in One Chart</a>, Burn and Grain</p>
What you need for this
- See price on AmazonAmazon
Foggy Bottom basswood plaques, 10 x 8 in, 5-pack
From Best Wood Blanks for Pyrography: Rounds, Plaques and Ornaments
- See price on AmazonAmazon
YIHUA 939D-VII 2-in-1 station, solid and wire pens
From Best Wood Burning Tools With Adjustable Temperature Control
- See price on AmazonAmazon
K KERNOWO 23-piece kit, dial 200-450 C, 14 tips
From Best Wood Burning Kit for Beginners: Starter Pens Compared