How-to
How to Shade Pyrography: Shader Tips, Heat Settings and Strokes
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Use a tip with a flat or rounded face: a shading tip, the flat of a universal tip, or a spoon shader on a wire burner. Set the heat about one band lower than for lines and build the tone in several light passes. On basswood that is the low band, about 400 to 550 F (200 to 290 C). Keep the tip moving, because a tip that stops leaves a blotch.
Gear for this job
All 7 picks comparedOutus pyrography wire nibs, 23 pieces, 23 shapes
See price on AmazonSee it on AmazonPlaid wood burning tips and stamps, set of 26
See price on AmazonSee it on AmazonCOHEALI pyrography wire tips, 69 pieces, 23 styles
See price on AmazonSee it on Amazon

This is for the stage where outlines come out clean but filled areas look patchy. Shading is the same burn as a line, spread over an area, so the controls are the same three: heat, time on the wood and pressure. The difference is that a wide tip face shows every pause and every change of speed. Smooth tone comes from cooler heat and repetition, not from one hot pass. The surface matters more here than anywhere else, since rough wood is one of the main causes of blotchy shading. Sand with the grain to 220 to 320 grit before you start.
What wood burning tip is best for shading?
Any tip with a broad face shades better than a point, because the heat is spread out and the edge does not dig in. Which one you use depends on the pen. The wood burning tip chart shows every shape named here.
| Tip | Pen type | Tone it lays down | Watch for |
|---|---|---|---|
| Shading tip (leaf or teardrop) | Solid-point | Soft band of tone, made with a very light touch | Blotches if held still, a hard edge if the rim lands first |
| Flat of the universal tip | Solid-point | Wide band when pulled sideways | The sharp corner digs in if the tip tilts |
| Spoon shader | Wire-nib | Soft tone with no hard edge, on flat or curved surfaces | Runs cooler than a fine nib at the same dial number |
| Spear shader | Wire-nib | Graduated tone that reaches into corners | The point burns darker than the belly |
| Flat or square shader | Wire-nib | Broad, even band over large areas | Stripes if the strokes do not overlap |
Heat settings for pyrography shading: lower heat, more passes
Shade about one heat band cooler than you burn lines on the same wood. For basswood, aspen and butternut that is the low band, 400 to 550 F (200 to 290 C). For birch, soft maple, cherry and walnut it is the medium band, 550 to 750 F (290 to 400 C). These are general guide ranges, since craft pens are not calibrated. Find the real setting on scrap with the temperature chart.
The setting is right when one pass leaves a pale tan and the tip still drags slightly on the wood. If a single pass gives the final dark tone, the heat is too high to shade with. A pen with one fixed heat cannot be turned down, so control the tone with speed: move faster, touch lighter and lift often. On a wire burner a broad shader runs cooler than a fine nib at the same dial number, so expect to turn the dial up a little after you swap from a writing nib.
Pyrography shading techniques: pull, circular and stipple
Three strokes cover almost all shading, and all three use the same light pressure. The pen makers' basic rule applies to each: the longer the tip stays on one spot, the darker the burn.
| Stroke | How to do it | Use it for |
|---|---|---|
| Pull stroke | Lay the face flat and pull toward you in overlapping bands, lifting off as each band ends | Gradients and shadows along an edge |
| Circular stroke | Small overlapping circles with the tip never stopping | Even tone over an area, soft backgrounds |
| Stipple | Touch and lift in dots with a flow, ball or cone tip. Closer dots give a darker tone | Texture, small spaces and tight corners |
Note.Start each stroke where the tone should be darkest. The tip cools as it travels across the wood, so the stroke fades on its own toward the end.
How to shade pyrography: a gradient practice strip
A gradient strip teaches the whole skill in about 20 minutes. Use an offcut of the same wood as the project, sanded the same way, and keep the finished strip as a tone reference for that wood.
- 1
Sand a scrap with the grain to 220 to 320 grit and wipe off the dust. Pencil a row of 5 boxes, each about 1 in (25 mm) square.
- 2
Fit the shader, set the heat at the bottom of the shading range for the wood and let the pen warm up. A solid-point pen needs 4 to 5 minutes.
- 3
Pass 1: cover all 5 boxes with one even layer of overlapping pull strokes. The result should be a pale tan. If it is already mid brown, turn the heat down one step and wait.
- 4
Pass 2: shade boxes 2 to 5 again. Pass 3: boxes 3 to 5. Pass 4: boxes 4 and 5. Pass 5: box 5 only. Do not change the heat or the pressure between passes.
- 5
If the tone turns patchy at the same speed, stop and clean the tip. Carbon on the tip blocks heat.
- 6
Repeat without box lines: burn one band about 5 in (125 mm) long that runs from pale to dark with no visible step between tones.
Blotchy pyrography shading: problems and causes
Match what you see to a row. Most shading faults trace back to one of three things: too much heat, a tip that paused or a rough surface.
| Problem | Cause | Fix |
|---|---|---|
| Dark blotches | Tip held still, or heat too high | Lower the heat one step and keep the tip moving |
| Dark dot at the start of each stroke | The tip landed before the hand was moving | Touch down and lift off while the hand is in motion |
| Hard edge around the shaded area | The rim or a corner of the tip touched first | Lay the face flat and lift off gradually as the stroke ends |
| Stripes | Strokes laid side by side with gaps, or too much heat | Overlap each stroke by about half, then add a pass across the first |
| Patchy tone, pale then dark | Carbon on the tip, or a rough surface | Clean the tip. Sand the next piece to 220 to 320 grit |
| Uneven tone that follows the grain | Soft and hard bands, as in pine and cedar, or open pores in oak | Lower heat and more passes, or move to basswood |
Note.A blotch that is already burned can be lightened with the side of a blade or 320-grit paper. See how to fix wood burning mistakes.
How to tell the pyrography shading is finished
Shading is done when the tones step evenly from the palest area to the darkest, there are no hard edges you did not intend, and the outlines still read clearly against the tone beside them. Hold the piece at arm's length. Unevenness that disappears at that distance does not need more work.
Stop one tone lighter than you think you need. A burn can always be darkened with another pass, while lightening it means scraping or sanding. Allow for the finish too: oil-based finishes darken the wood, so pale shading loses some of its contrast under them. Light burns also fade in sunlight more than dark ones. Both points are covered in how to seal pyrography.
Quick answers
Short answers on shader tips, heat settings and strokes for pyrography shading. Each one is explained in more detail above.
- What wood burning tip is best for shading? The shading tip on a solid-point pen and a spoon shader on a wire-nib burner. The flat of a universal tip also works.
- What is a pyrography spoon shader? A wire nib with a small, slightly dished oval face. It lays down soft tone with no hard edge on flat and curved surfaces.
- What heat is used for pyrography shading? About one band below your line setting. On basswood that is the low band, 400 to 550 F (200 to 290 C). Confirm on scrap.
- Why is my pyrography shading blotchy? The tip is too hot, it paused on the wood or the surface is rough. Lower the heat, keep moving and sand finer.
- Can you shade with a one-heat wood burning pen? Yes. Control the tone with speed and a light touch, in quick overlapping passes.
What you need for this
- See price on AmazonAmazon
Outus pyrography wire nibs, 23 pieces, 23 shapes
From Best Wood Burning Tip Sets and Replacement Tips by Pen Type
- See price on AmazonAmazon
YIHUA 939-VI dual pen station, 23 wire nibs
From Best Wire Tip Wood Burners: Pyrography Machines Compared
- See price on AmazonAmazon
YIHUA 939D-VII 2-in-1 station, solid and wire pens
From Best Wood Burning Tools With Adjustable Temperature Control
- See price on AmazonAmazon
Foggy Bottom basswood plaques, 10 x 8 in, 5-pack
From Best Wood Blanks for Pyrography: Rounds, Plaques and Ornaments