Tool
Wood Burning Pen Temperature Chart: Settings by Wood Species and Tip
Pick your wood, the job and your kind of pen to get a starting range, then confirm it on scrap. Craft pens are not calibrated, so every figure here is a range.
Short answer
Most wood burning is done at about 550 to 750 F (290 to 400 C) at the tip, where pale wood turns toast brown. Soft woods such as basswood start lower, at 400 to 550 F (200 to 290 C), and hard maple or oak need 750 to 950 F (400 to 510 C). Shade one band cooler than you draw. These are general guide ranges: set the real heat on a scrap of the same wood.
What temp for a wood burning pen?
| Band | Tip temperature | Mark on pale wood | Use it for |
|---|---|---|---|
| Low | 400 to 550 F (200 to 290 C) | pale tan to light brown | shading and soft woods (basswood, aspen, butternut), cedar |
| Medium | 550 to 750 F (290 to 400 C) | mid "toast" brown | lines on most woods; the general starting point |
| High | 750 to 950 F (400 to 510 C) | dark brown to near black | lines on hard maple, oak, bamboo; fast dark lines |
| Very high | above 950 F (above 510 C) | black, cuts into the surface; wire-nib burners only | not needed for ordinary flat work |
Wood burning temperature chart by material
| Material | Janka hardness (lbf) | Lines and writing tips | Shading tips | Note |
|---|---|---|---|---|
| Basswood | 410 | Low to medium400 to 750 F(200 to 400 C) | Low400 to 550 F(200 to 290 C) | The standard. Burns evenly |
| Aspen | 350 | Low to medium400 to 750 F(200 to 400 C) | Low400 to 550 F(200 to 290 C) | Very soft: a hot tip sinks in |
| Butternut | 490 | Low to medium400 to 750 F(200 to 400 C) | Low400 to 550 F(200 to 290 C) | Coarser texture than basswood |
| Yellow poplar | 540 | Medium550 to 750 F(290 to 400 C) | Low to medium400 to 750 F(200 to 400 C) | Green or grey streaks show through |
| Birch (and birch plywood face) | 910 to 1,260 | Medium to high550 to 950 F(290 to 510 C) | Medium550 to 750 F(290 to 400 C) | On plywood stay in the face veneer |
| Soft maple | 950 | Medium to high550 to 950 F(290 to 510 C) | Medium550 to 750 F(290 to 400 C) | |
| Cherry | 950 | Medium to high550 to 950 F(290 to 510 C) | Medium550 to 750 F(290 to 400 C) | Reddish wood, less contrast |
| Walnut | 1,010 | Medium to high550 to 950 F(290 to 510 C) | Medium550 to 750 F(290 to 400 C) | Dark wood, low contrast |
| Hard maple | 1,450 | High750 to 950 F(400 to 510 C) | Medium to high550 to 950 F(290 to 510 C) | Crisp lines, slow going |
| Oak | 1,220 to 1,360 | High750 to 950 F(400 to 510 C) | Medium to high550 to 950 F(290 to 510 C) | Open pores break up lines |
| Pine (eastern white) | 380 | Low to medium400 to 750 F(200 to 400 C) | Low400 to 550 F(200 to 290 C) | Soft and hard bands burn unevenly; resin |
| Cedar (western red) | 350 | Low400 to 550 F(200 to 290 C) | Low400 to 550 F(200 to 290 C) | Soft, strong grain, uneven |
| Bamboo | about 1,380 | High750 to 950 F(400 to 510 C) | Medium to high550 to 950 F(290 to 510 C) | Glued strips: glue lines burn differently |
| Basswood plywood face | as basswood | Low to medium400 to 750 F(200 to 400 C) | Low400 to 550 F(200 to 290 C) | Stay in the face veneer, never into the glue |
| Cork | no figure | Lowest wood settings; no verified temperature | Same | Walnut Hollow lists cork in dial zones 2 and 3 of 4 |
| Vegetable-tanned leather | no figure | Lowest settings on the dial; no verified temperature | Same | Walnut Hollow lists leather in dial zones 1 and 2 of 4. Never chrome-tanned or faux leather |
Burn and Grain - burnandgrain.com/tools/wood-burning-temperature-chart. General guide ranges. Craft pens are not calibrated, so confirm on scrap.
Find the starting heat for your wood and pen
Pick the material, the job and your kind of pen. The answer is a row of the chart above, turned into a setting for that pen.
Starting heat: Basswood, lines and writing
Low to medium400 to 750 F (200 to 400 C)
- Mark to aim for
- pale tan to light brown to start
- On your pen
- Start in the lower part of the dial. On Walnut Hollow's four-zone dial, wood starts in zone 2. Then raise it if the line is too pale. Zones are not degrees. Let the pen heat for 4 to 5 minutes after each change.
- Watch for
- The standard. Burns evenly.
A general guide range, not a measurement: a dial number or color zone is not a temperature. Confirm the setting with the scrap test below. Your pen maker's instructions win where they differ.
The scrap test that sets the real number
- 1
Take an offcut of the same wood, sanded the same way as the project.
- 2
Fit the tip you will use. Set the pen at the bottom of the suggested range and let it heat (4 to 5 minutes for a solid-point pen).
- 3
Draw a row of straight strokes at your normal, steady speed with light pressure.
- 4
Raise the heat one small step, wait, and draw another row. Repeat.
- 5
Stop at the first setting that gives an even toast-brown line while you still feel the tip drag slightly on the wood.
- 6
If the tip glides with no drag and the line is black with a scorched halo, the heat is too high: go back one step.
- 7
Write the dial position on the scrap and keep it with the project. Repeat the test when you change tip or wood.
Steps 5 and 6 follow Colwood's guidance on tip drag and toast color. The 4 to 5 minute heat-up is from Walnut Hollow's instructions.
How hot does a wood burning tool get?
| Pen | Type | Maker's figure |
|---|---|---|
| Walnut Hollow Creative Versa-Tool | solid, dial with 4 color zones | up to 950 F (510 C) |
| Weller 25 W woodburning kit | solid, fixed heat | 900 F (480 C) on retailer listings; 526 C maximum on Weller's page |
| Walnut Hollow Creative Woodburner | wire nib, dial | about 600 to 1000 F (316 to 538 C) |
| Razertip SS-D10 | wire nib, dial 1 to 10 | about 170 to 745 C |
| Razertip P80 | wire nib | about 180 to 1400 F |
| Razertip SL | wire nib | up to about 900 C (1650 F) |
| TRUArt Stage 2, 60 W | wire nib, digital | 1550 F (843 C) maximum |
| Colwood | wire nib | about 700 F for a "toast" brown; 1500 F or more possible |
How the numbers are worked out
The chart is built from three rules. First, the band for lines follows hardness, after Colwood's advice to set the unit higher for harder wood and lower for softer wood. A Janka hardness under 500 lbf gives low to medium, 500 to 900 gives medium, 900 to 1,100 gives medium to high, and above 1,100 gives high. Cedar is set to low because of its very soft grain. The hardness figures come from The Wood Database and the standard Janka table.
Second, shading runs one band cooler than lines on the same wood and is built up in passes. This is standard teaching practice, not a maker's figure.
Third, the degrees attached to each band are this site's four bands. They are a general guide built from published anchor points, not a maker's table: wood chars only with prolonged exposure below about 392 F (200 C) and forms char at about 550 F (300 C) (USDA Forest Products Laboratory); about 700 F gives a "toast" brown (Colwood); fixed-heat craft pens are listed at 900 to 950 F (Weller, Walnut Hollow); wire-nib units are listed up to 1000 to 1650 F (Walnut Hollow, Razertip, TRUArt, Colwood).
Left out because it could not be verified: a separate temperature column for wire nibs, because no maker publishes different target temperatures for them (the lookup gives dial guidance instead), and degree figures for leather and cork, where hobby sources disagree by several hundred degrees, so the chart gives dial positions only.
For the shape of each tip and what it is for, see the wood burning tip chart.
Before you burn
Note.These are general guide ranges, not measurements. Craft pens are not calibrated: a dial number or color zone is not a temperature. Where your pen maker's instructions differ, the instructions win.
- Burn only bare, untreated wood. Never burn pressure-treated, painted, stained or varnished wood, MDF or particle board.
- Leather: vegetable-tanned only.
- Work with ventilation, and keep the fan from blowing across the tip.
- The tip and barrel cause burns. Use the stand and let the pen cool before changing tips.
Sources: Walnut Hollow instructions, Weller, Razertip, TRUArt, Colwood, USDA Forest Products Laboratory, The Wood Database.
Read next
- Wood for pyrography: which species show a burn best.
- How to use a wood burning tool: the first session, step by step.
- Wood burning pen not working: the causes, in order.