Tool
Wood Burning Tip Chart With Pictures: Solid Tips and Wire Nibs
Find the tip in your kit by its shape, then read across for the mark it makes, the job it does and the heat to start at.
Short answer
Three tips do most of the work. A universal tip, a small angled wedge, draws lines on its edge and fills on its flat. A rounded flow or ball tip writes and makes dots, because it glides in any direction. A flat shader lays down tone at low heat. Fine points (cone, tapered) are for detail, and the transfer, stamp and hot knife tips are not for drawing at all.
Which tip for which job
| Job | Solid tip | Wire nib |
|---|---|---|
| Outlines and straight lines | universal (on its edge), cone | skew, rounded-heel knife |
| Writing and cursive | flow, mini flow, ball | writing nib, ball stylus |
| Thick-and-thin lettering | calligraphy | calligraphy nib |
| Shading | shading tip, flat of the universal | spoon shader, spear shader, flat shader |
| Fine detail and dots | cone, tapered, mini flow | ball stylus, writing nib |
| Names and dates without freehand | letter and number stamps | none |
| Transfer a laser print | transfer tip | flat shader (Razertip sells a 7 mm transfer/shader) |
| Cutting stencil film, foam, deco mesh | hot knife, tapered | none |
Tip finder: pick the job, see the tips
Choose your kind of pen and what you want to do. The cards are rows of the chart below, the tips made for the job first.
5 tips for writing and lettering
Calligraphysolid tip
Thick-and-thin lettering, borders, square shading. Walnut Hollow: "basic calligraphy style lettering".
Start at: Medium, 550 to 750 F (290 to 400 C)
Watch for: Stroke width changes if the pen angle changes mid-letter.
Flowsolid tip
Curves, dots, dot shading, cursive writing (Walnut Hollow).
Start at: Medium, 550 to 750 F (290 to 400 C)
Watch for: Line is wider than expected; slow hand gives blobs.
Mini flowsolid tip
Small dots, circles, small cursive writing (Walnut Hollow).
Start at: Low to medium, 400 to 750 F (200 to 400 C)
Watch for: Thin tip loses heat on long strokes: work in short strokes.
Ballsolid tip
Dots, stippling, smooth writing.
Start at: Medium, 550 to 750 F (290 to 400 C)
Watch for: Presses a dent into soft wood.
Letter and number stampssolid tip
Names, dates and initials without freehand lettering.
Start at: Medium to high, 550 to 950 F (290 to 510 C)
Watch for: Letters are mirrored on the stamp; uneven dwell gives uneven darkness.
General guide ranges. Craft pens are not calibrated, so confirm on scrap. Tip names and uses follow the makers' own descriptions. Your pen maker's instructions win where they differ.
Wood burning tips chart: solid brass tips
Threaded tips for a solid-point pen, 14 shapes. Each drawing shows the tip from the side, pointing right, with the threaded end on the left.
| Shape | Tip (other names) | Mark it makes | Used for | Starting heat | Watch for |
|---|---|---|---|---|---|
| Universalall-purpose, standard | Thin line on the edge, medium line when tilted, wide band when pulled sideways | Outlines, straight lines, curves, filling with the flat. Walnut Hollow: "performs all fundamental woodburning techniques" | Medium550 to 750 F(290 to 400 C) | The sharp corner digs in and follows the grain on curves | |
| Mini universal | Thin to medium line | Small outlines and tight curves | Medium550 to 750 F(290 to 400 C)low on basswood | Same as universal; easy to overburn small details | |
| Calligraphychisel | Thick stroke pulled sideways, thin stroke pulled along the edge | Thick-and-thin lettering, borders, square shading. Walnut Hollow: "basic calligraphy style lettering" | Medium550 to 750 F(290 to 400 C) | Stroke width changes if the pen angle changes mid-letter | |
| Flowround, rounded | Even medium line in any direction, round dots | Curves, dots, dot shading, cursive writing (Walnut Hollow) | Medium550 to 750 F(290 to 400 C) | Line is wider than expected; slow hand gives blobs | |
| Mini flow | Fine even line, small dots | Small dots, circles, small cursive writing (Walnut Hollow) | Low to medium400 to 750 F(200 to 400 C) | Thin tip loses heat on long strokes: work in short strokes | |
| Conepointed | Fine line, pin dots | Fine lines, dots, curves, stippling | Low to medium400 to 750 F(200 to 400 C) | Point catches in the grain and burns a dot where it lands | |
| Taperedneedle | Extra-fine line | Extra-fine detail; Walnut Hollow also uses it to cut stencil material on glass | Low to medium400 to 750 F(200 to 400 C) | Bends if pressed; scratches the wood instead of burning when too cool | |
| Shadingshader, leaf, teardrop | Soft band of tone; leaf shape when pressed flat | Shading and gradients "with a very light touch" (Walnut Hollow), leaf stamps | Low to medium400 to 750 F(200 to 400 C) | Blotches when held still; hard edge if the rim touches first | |
| Transferdisc | No mark on wood: it heats paper | Rubbing the back of a laser print or photocopy so the toner moves to the wood. Image comes out mirrored | Medium to high550 to 950 F(290 to 510 C) | Scorches the paper if left still: keep it moving and lift the paper often to check | |
| Hot knifeblade | A cut, not a burn | Cutting foam, stencil film, deco mesh on glass or tile (Walnut Hollow: "cuts and shapes a variety of materials") | Per material, on scrap first | Not a drawing tip. Plastic fumes: ventilate | |
| Hot stamp pointspattern stamps: square, star, circle | One repeated shape | Borders and patterns | Medium to high550 to 950 F(290 to 510 C) | Uneven impression: press firmly and rock the point on all sides (Walnut Hollow) | |
| Letter and number stampsalphabet tips | One letter or digit per press | Names, dates and initials without freehand lettering | Medium to high550 to 950 F(290 to 510 C) | Letters are mirrored on the stamp; uneven dwell gives uneven darkness | |
| Balldot | Round dots, smooth even line | Dots, stippling, smooth writing | Medium550 to 750 F(290 to 400 C) | Presses a dent into soft wood | |
| Soldering point | Not for wood | Joining metal with solder. Included in multi-use kits | Not a wood tip | Sold in "wood burning" kits to raise the tip count |
Wire nibs for wire-nib burners
Ten nib shapes. The two heavy lines on the left of each drawing are the posts of the pen that hold the wire.
| Shape | Nib (other names) | Mark it makes | Used for | Starting heat | Watch for |
|---|---|---|---|---|---|
| Writing nibwriter, drawing point | Even line in any direction | Writing, signing, general drawing. Razertip: used "much like a ball-point pen" | Medium550 to 750 F(290 to 400 C) | Rotating the nib changes the line weight | |
| Ball stylusball point | Very even line, dots | Writing, dot shading, burnishing. Line width is the same in every direction (Razertip) | Medium550 to 750 F(290 to 400 C) | Dents soft wood under pressure | |
| Skewknife | Crisp thin line, cuts slightly into the surface | Straight lines, outlines, hair and feather detail | Medium550 to 750 F(290 to 400 C) | The toe digs in on curves; needs sharpening | |
| Rounded-heel knife | Crisp line that turns without digging | Curved outlines, general line work. Colwood rounds the heel "to prevent digging into the wood" | Medium550 to 750 F(290 to 400 C) | Less sharp in tight corners than a skew | |
| Spoon shader | Soft tone with no hard edge | Shading on flat, concave and convex surfaces. Razertip calls its medium spoon shader its most popular shading tip | Low to medium400 to 750 F(200 to 400 C) | Runs cooler than a fine nib at the same dial number: turn up a little | |
| Spear shader | Graduated tone into a point | Graduated shading and reaching into acute corners | Low to medium400 to 750 F(200 to 400 C) | The point burns darker than the belly | |
| Flat shadersquare shader; Colwood S, 3/16 in | Broad even band | Covering large areas of shading quickly; a flat plate also works for toner transfer | Low to medium400 to 750 F(200 to 400 C) | Stripes if strokes do not overlap | |
| Calligraphy nibColwood C1 small, C2 large | Thick-thin strokes; a corner writes, the wide edge shades | Lettering and shading. Described as "three tips in one" | Medium550 to 750 F(290 to 400 C) | Angle must stay constant through a letter | |
| Tight roundsmall round; Colwood J | Thin line that turns on a tight radius | Tight curves; laid flat, shading in small spaces | Medium550 to 750 F(290 to 400 C) | Easy to overburn at the start of a stroke | |
| Specialty nibsfish scale, circle, double line | One repeated shape or two parallel lines | Scales, circles, parallel lines on carvings. Colwood fish-scale tips come in 1/4, 3/16 and 1/8 in | Medium550 to 750 F(290 to 400 C) | Narrow use: not needed for flat work |
General guide ranges. Craft pens are not calibrated, so confirm on scrap. Drawings show approximate proportions: brands differ, and makers do not publish tip dimensions except where a size is given.
Burn and Grain - burnandgrain.com/tools/wood-burning-tip-chart. General guide ranges. Craft pens are not calibrated, so confirm on scrap.
Notes on the chart
- Tip names differ by brand. Walnut Hollow calls them points, wire burner makers call them tips or nibs.
- Starting heat is a general guide in our four bands. Set the real heat on a scrap of the same wood. The wood burning temperature chart gives a range for each wood.
- On a wire-nib burner a fine nib runs hotter than a heavy shader at the same dial number (Razertip). Turn down when you switch to a finer nib.
- Tips are not universal between brands. See are wood burning tips universal.
- Change solid tips only when the pen is cold, with pliers.
How to read this chart
Find your tip by its outline. A solid tip is drawn with its threaded shank and collar on the left. A wire nib is drawn with the two posts of the pen. Then read across: the mark the tip leaves, the jobs it is used for, a heat band to start from and the usual mistake.
The starting heat column uses the four heat bands of this site:
| Band | Tip temperature | Mark on pale wood |
|---|---|---|
| Low | 400 to 550 F (200 to 290 C) | pale tan to light brown |
| Medium | 550 to 750 F (290 to 400 C) | mid "toast" brown |
| High | 750 to 950 F (400 to 510 C) | dark brown to near black |
| Very high | above 950 F (above 510 C) | black, cuts into the surface; wire-nib burners only |
Names and uses of the solid tips follow Walnut Hollow's Creative Versa-Tool instructions and listing. Ball, dot and stamp tips are named as in TRUArt tip set listings. Names and uses of the wire nibs follow Colwood's tip usage page, Razertip product pages, the Walnut Hollow Creative Woodburner guide and Fox Chapel's "Wood Burning Tips and Textures".
The outlines are drawn from the makers' own tip pictures. Sizes are approximate, except the sizes Colwood publishes. The starting heat and the "watch for" column are a general hobby guide, not a maker's figure. Where your pen's instructions say something different, the instructions win.
Left out because it could not be verified: exact dimensions of solid tips by brand, thread sizes other than the M4 x 0.7 that TRUArt states, and the shapes of unnamed pattern tips in generic kits.
Read next
- Wood for pyrography: which species show a burn best.
- How to use a wood burning tool: the first session, step by step.
- Wood burning pen not working: the causes, in order.