How-to
How to Use a Wood Burning Tool: Setup, First Lines and Cooldown
Published Updated
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Fit the tip while the pen is cold, set the pen on its stand and let it heat: 4 to 5 minutes for a solid-point pen, far less for a wire nib. Hold it like a large pencil, use light pressure and pull steady strokes on a scrap of the same wood until the line is toast brown. Then burn the project, switch off, let the pen cool completely and take the tip out with pliers.
Gear for this job
All 7 picks comparedK KERNOWO 23-piece kit, dial 200-450 C, 14 tips
See price on AmazonSee it on AmazonWEP 939D-V wire-nib station, 30 W, LED read-out
See price on AmazonSee it on AmazonArtSkills Wood Burning Tool Kit, 16 Pieces
See price on AmazonSee it on Amazon

This is for a new owner with the kit open on the table. Wood burning tool, wood burning pen, wood burner and pyrography pen all mean the same thing. What decides the first result is three things you control: heat, speed and pressure. Craft pens are not calibrated, so the dial gives zones or numbers, not degrees, and the right setting is found on scrap, not read off the dial. Pale, soft, even-grained wood such as basswood makes the first lines much easier. Plan a full page of test strokes before the real piece.
How does a wood burning pen work?
A solid-point pen works like a soldering iron: a heating element in the barrel heats a threaded brass tip. It takes about 4 to 5 minutes to heat (Walnut Hollow) and has either one fixed heat or a dial. A wire-nib burner has a power unit with a numbered dial and a light pen. It passes current through a tip of bent nichrome wire, which heats and cools quickly.
Either way the mark is scorched wood. The US Forest Products Laboratory puts char formation at about 550 F (300 C), and below about 392 F (200 C) wood chars only with prolonged exposure. Fixed-heat craft pens are listed at 900 to 950 F (480 to 510 C), which is why speed matters: the longer the tip stays in one place, the darker the burn.
What you need before using a wood burning pen kit
Set up the whole table before the pen is plugged in. Once it is hot, one hand is always busy, and the tip must never be left lying on the work surface.
- The pen, its stand and tape. Walnut Hollow says to tape the stand to the work table.
- Pliers for changing solid tips, or the tweezer tool supplied with a wire-nib burner.
- A blank of pale, bare wood and a scrap of the same wood. Basswood (Janka 410 lbf) is the standard choice: see wood for pyrography.
- Sandpaper, 220 to 320 grit, and a cloth to wipe off the dust.
- A fan or extractor that pulls smoke away from your face without blowing on the tip. More in is pyrography safe.
Note.Burn only bare, untreated wood. Never pressure-treated, painted, stained or varnished wood, MDF or particle board.
How to set up a wood burning tool and burn the first lines
The steps are written for a solid-point pen with a dial, the usual starter tool. Notes for fixed-heat pens and wire-nib burners are inside the steps.
- 1
Sand the blank and the scrap with the grain to 220 to 320 grit and wipe off the dust. A rough surface is one cause of blotchy burns.
- 2
Tape the stand to the table. Lay the cord so it runs behind your burning hand and cannot drag across the work.
- 3
With the pen cold and unplugged, screw in the universal tip by hand and snug it with pliers. On a wire-nib burner fit the writing nib with the power off.
- 4
Plug in and set a low heat: zone 2 of 4 on a Walnut Hollow dial, or near the bottom of the dial on a wire-nib unit. A fixed-heat pen has no setting to choose.
- 5
Leave the pen on the stand for 4 to 5 minutes. A wire nib is ready far sooner. Do not test the tip with a finger: touch it to the scrap.
- 6
Hold the pen like a large pencil, on the grip, well back from the metal. Rest the side of your hand on the wood and keep the pressure light.
- 7
On the scrap, pull 5 or 6 straight lines about 2 in long, each at a different speed. The slow ones come out darker. Look for an even toast-brown line at a pace you can hold.
- 8
If the steady line is too pale, raise the dial one step, wait 4 to 5 minutes and repeat. If it is black and the tip glides with no drag, the heat is too high: turn it down.
- 9
Burn the project in short strokes. Set the tip down already moving and lift it while still moving, so no dark dot forms at either end. On curves turn the wood, not your wrist.
- 10
Switch off and unplug. Leave the pen on the stand until it is completely cool, then take the solid tip out with pliers so it cannot seize.
Speed, pressure and heat: holding the pen for a clean line
Use light pressure. Walnut Hollow's instructions say light pressure is best and that the burn gets darker the longer the point stays on the surface. Pressing harder does not replace heat. On soft wood it digs the tip in and makes the line follow the grain.
Colwood's rules tie the settings together: a slow hand needs less heat and a fast hand more, harder wood takes a higher setting and softer wood a lower one, and too much heat makes lines too wide. For basswood the starting band for lines is low to medium, 400 to 750 F (200 to 400 C). The temperature chart lists the band for each wood and turns it into a dial position.
How to tell your first pen lines are right
Judge the scrap, not the dial. A good first line is toast brown and even in color and width from end to end, with a slight drag felt through the pen. The table shows the common faults and the one change to make for each.
The job is done when the lines on the piece match the test line. Then erase or lightly sand off any pattern lines with 220 to 320 grit and seal the wood: see how to seal pyrography.
| What the line looks like | What it means | Change one thing |
|---|---|---|
| Pale and patchy | Too cool, or the hand is too fast | Slow down first, then raise the heat one step |
| Black and wide, tip glides with no drag | Heat too high (Colwood) | Turn the dial down, or move faster on a fixed-heat pen |
| Dark dots at the start or end | The tip paused on the wood | Land and lift while moving |
| Line wanders along the grain | Too much pressure, or the sharp corner of the tip digging in | Lighter touch, or a rounded flow tip for curves |
Changing wood burning tips safely
On a solid-point pen, never change a tip hot. Switch off, let the pen cool completely, then unscrew the tip with pliers and fit the next one. Each change costs the cooling time plus another 4 to 5 minutes of heating, so plan the work by tip: all outlines first, then all shading. On a wire-nib burner turn the power off, then swap the nib with the tweezer tool or swap the whole pen. Wire nibs cool quickly, so the wait is short.
Tips are not universal between brands. Which shape does which job is laid out in the tip chart. For a tip that will not come out, see how to change wood burning tips.
Cooldown and storage of the pen and tips
Switch off at the dial and unplug. Colwood's rule is to turn the unit off whenever you leave it. Leave the pen on its stand until it is completely cool before it goes back in the box. Walnut Hollow's sheet gives no cooling time, so do not hurry it. Take solid tips out after every session, cold, with pliers: left in, they can seize in the barrel. A little dry graphite lubricant on the threads makes the next change easier.
Choosing a first project once the tool is set up
Once a pen is heated and the basics of tip contact and pressure are familiar, the next question is what to burn first. Flat, lightly sanded wood such as basswood or birch plywood is a common general choice, and simple shapes with clear lines tend to be easier than shaded portraits. A list of beginner wood burning project ideas can help here, since it groups simple designs such as coasters, bookmarks and plaques by how little skill and time they typically ask for. Starting with one small piece also keeps wood and practice time modest while the hand learns to keep a steady speed.
Quick answers
Short answers for a first session. Dial zones and numbers are not degrees, so every setting is confirmed on a scrap of the same wood.
- How do you use a wood burning pen for beginners? Fit the tip cold, heat the pen 4 to 5 minutes, test on scrap with light pressure, then burn in short steady strokes.
- How does a wood burning pen work? A solid pen heats a brass tip from an element in the barrel. A wire-nib burner passes current through a nichrome wire tip.
- How long does a wood burning tool take to heat up? About 4 to 5 minutes for a solid-point pen, by Walnut Hollow's instructions. A wire nib heats quickly.
- How hard should you press with a pyrography pen? Lightly. The tone comes from heat and time on the wood, not from pressure.
- How do you set up a wood burning kit? Tape down the stand, fit the tip cold, put the cord behind your hand and start at a low heat.
What you need for this
- See price on AmazonAmazon
K KERNOWO 23-piece kit, dial 200-450 C, 14 tips
From Best Wood Burning Kit for Beginners: Starter Pens Compared
- See price on AmazonAmazon
YIHUA 939D-VII 2-in-1 station, solid and wire pens
From Best Wood Burning Tools With Adjustable Temperature Control
- See price on AmazonAmazon
Foggy Bottom basswood plaques, 10 x 8 in, 5-pack
From Best Wood Blanks for Pyrography: Rounds, Plaques and Ornaments
- See price on AmazonAmazon
Outus pyrography wire nibs, 23 pieces, 23 shapes
From Best Wood Burning Tip Sets and Replacement Tips by Pen Type