Explainer
What Is Wood Burning Paste and Gel Made Of, and How Does It Work?
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Short answer
Wood burning paste, also sold as wood burning gel or torch paste, is a thick heat-activated compound. You spread it through a stencil in a thin layer and darken it with a heat gun. The maker pages checked for this page list no ingredients. The published homemade version is ammonium chloride in water, about 1 tablespoon per 100 mL, which heat breaks down so that the wood darkens.
Gear for this job
All 7 picks comparedTorch Paste wood burning paste, 3 oz jar
See price on AmazonSee it on AmazonOYACH wood burning paste gel kit, 6 oz, 19 pieces
See price on AmazonSee it on AmazonBIGTHUMB wood burning gel kit, 4 oz with scraper
See price on AmazonSee it on Amazon

This page is for someone who has seen gel-burned signs and wants to know what the stuff is before buying a jar or heating it indoors. Two things are worth separating: what the brands say about their own products, and what published do-it-yourself recipes contain. They are not proof of each other. This site names an ingredient for a product only when the maker's label or safety data sheet does, and it gives no safety verdict of its own. The steps and figures below come from maker instructions and the sources listed at the end.
What is wood burning paste or gel used for?
It is used to put a burned-looking design on bare wood without a hot pyrography pen. The paste goes on cold through a stencil. Nothing shows as a burn until a heat gun passes over it. Because it is thick, it stays inside the stencil opening better than thin marker fluid, which is why sign makers use it for lettering.
Wood burning paste, wood burning gel, burn paste and torch paste are names for the same kind of product. Torch Paste is a brand, and its maker describes it as formulated to minimize leaks under reusable or one-time stencils. It lists wood, cardboard, card stock and denim as surfaces. The gel and paste guide compares jars by size and applicator.
What is wood burning paste made of?
For the commercial jars, the honest answer is that the makers do not say. The table shows what each source publishes. The two homemade recipes name ammonium chloride. That does not establish what is in any branded jar.
| Source | Product or recipe | What it says about contents |
|---|---|---|
| Torch Paste product page | Torch Paste, 3 oz jar | No ingredients listed. States that it conforms to ASTM D-4236 |
| Scorch Marker, How It Works | Scorch Marker and Scorch Paint | No ingredients listed. Describes a chemical reaction in the wood under heat |
| Make:, Chemical Woodburning | Homemade liquid | 1 tablespoon ammonium chloride per 100 mL warm water |
| Jennifer Maker, stencil burning | Homemade gel | 1 tablespoon ammonium chloride, 8 teaspoons food thickener, 1/2 cup warm water |
Note.ASTM D-4236 is a labeling practice for art materials. A statement of conformance is not an ingredient list, and this site draws no safety conclusion from it.
How does wood burning gel darken the wood?
Make: explains the chemistry for the ammonium chloride recipe. On heating, ammonium chloride breaks down into ammonia gas and hydrochloric acid. The ammonia drifts off. The acid stays in the wood fibers and burns them. Under a heat gun on high, Make: describes the treated area going yellow, then brown, then brownish-black within one to two minutes.
The treated wood darkens at a lower temperature than bare wood chars. Scorch Marker gives about 350 F for its reaction. The US Forest Products Laboratory puts char formation in untreated wood at about 550 F. So the design turns brown while the wood around it stays pale, as long as the heat gun keeps moving.
How to use wood burning paste with a stencil and heat gun
These steps follow the instructions Torch Paste publishes for its own jar. Other brands differ in wait time and in the heat they ask for, so read the label of the jar you have. Start on a scrap of the same wood.
- 1
Sand bare, unfinished wood with the grain to about 220 grit and wipe off the dust. Scorch Marker asks for 240 grit for its brush-on product.
- 2
Lay the stencil and rub it down well so every edge sits tight to the wood. The maker names adhesive stencils and says plastic ones work well too.
- 3
Spread a thin layer of paste across the openings with a squeegee. The maker stresses that a little goes a long way.
- 4
Scrape the excess off the stencil and return it to the jar, then lift the stencil straight up.
- 5
Let the paste absorb and dry for at least 2 to 3 minutes before any heat touches it.
- 6
Heat with a gun that reaches 400 C or more (the maker also gives at least 775 F and 1000 W or more). Move it over the design until the design burns.
- 7
Let the surface cool, then wipe away the debris with a dry cloth and apply a finish.
Wood burning gel tips: bleeding and patchy color
Most failures come from too much paste, a loose stencil or too little heat. A hair dryer is not hot enough for these products. The rows below pair what you see with the likely cause.
| What you see | Likely cause | What to do |
|---|---|---|
| Fuzzy edges, color under the stencil | Stencil not pressed down, or a thick layer | Rub the edges down. Apply thin and scrape off the excess |
| Design spreads along the grain | Soft or rough wood, or a thin, runny compound | Sand smoother. Use pale, even-grained wood and a thick paste |
| Design stays pale or yellow | Heat source not hot enough | Use a preheated heat gun of the wattage the label names |
| Patchy color in one shape | Uneven layer or uneven heat | Spread one even pass. Keep the gun moving over the whole design |
| Bare wood around the design browns | Gun held still or too long in one place | Keep it moving and stop once the design is dark |
Is wood burning paste safe? What the makers say
This site gives no verdict. It can only report what is published. Torch Paste says to burn using goggles and protective gear in a well-ventilated area, and to keep the jar away from children 12 and under. It says the paste is meant for unfinished surfaces, because sealer, stain or paint may give off harmful fumes when heated. For anything that touches food, it recommends sealing the burned surface with a food grade sealer.
For the homemade recipes the sources are more direct. Make: tells readers to wear gloves and safety goggles, to work with plenty of ventilation and to avoid breathing the dust or vapor. It warns that ammonium chloride fumes can cause respiratory harm or an asthma-like allergy. Jennifer Maker asks for a respirator and eye protection. General ventilation advice is in is pyrography safe.
Wood burning without ammonium chloride: pen or paste?
Because the brands checked here publish no ingredients, this site cannot say which jars contain ammonium chloride and which do not. If you want to know, ask the maker for the safety data sheet of the exact product before buying.
The method that certainly involves no compound is direct heat: a hot wood burning pen burns the line itself. The page on a scorch marker vs a wood burning pen compares the two routes. If you already own a craft cutter, wood burning with a Cricut covers the vinyl stencil for paste.
Quick answers
Short answers to the searches people type about wood burning paste and gel. Figures are the makers' own, as given above.
- What is wood burning gel made of? The maker pages checked list no ingredients. Published homemade versions are ammonium chloride in water, thickened for stencil use.
- What is wood burning paste used for? Stenciled designs and lettering on bare wood: signs, coasters, wood slices. Heat from a heat gun turns the paste area brown.
- Is wood burning with torch paste done with a torch? No. Torch Paste is a brand name. Its instructions call for a heat gun that reaches 400 C or more.
- Is wood burning gel the same as a scorch marker? The idea is the same: a heat-activated compound. Gel is thick for stencils, and marker fluid is thin for drawing.
What you need for this
- See price on AmazonAmazon
Torch Paste wood burning paste, 3 oz jar
- See price on AmazonAmazon
ROMECH 1500 W heat gun, variable 120 to 1200 F
- See price on AmazonAmazon
Eageus metal letter stencils, 8 pieces, 4 x 7 in
From Best Wood Burning Stencils: Metal, Reusable and Letter Sets
- See price on AmazonAmazon
Scorch Marker Pro, bullet and brush tips, 1 marker
From Best Wood Burning Markers: Scorch Pens and Chemical Burn Pens