Wood Burning Portraits: Photo, Transfer, Tips and Shading
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedYIHUA 939-VI dual pen station, 23 wire nibs
See price on AmazonSee it on AmazonWEP 939D-VI dual pen station with LED display
See price on AmazonSee it on AmazonWEP 939D-V wire-nib station, 30 W, LED read-out
See price on AmazonSee it on Amazon
A wood burning portrait is built the way a graphite drawing is: a light transferred outline, then many low-heat layers of shading that slowly darken toward the shadows, finished with fine detail in the eyes and hair. The two things that decide success are a photo with strong light and shadow, and a wire-nib burner run cooler than you would use for lines. This page walks through the process for both human and pet portraits.
Choose a photo that will burn well
Pick a sharp photo with one clear light source, so one side of the face is lit and the other falls into shadow. Flat, front-flash photos look fine on a phone but give you nothing to shade. The face should fill most of the frame and be at least 1000 pixels tall so you can zoom in on the eyes.
Convert the photo to grayscale and push the contrast a little. This shows you the tonal map you will burn: pale highlights on the forehead, nose and cheekbones, mid-tones on the cheeks, dark tones under the chin, in the nostrils, between the lips and in the pupils. Some pyrographers posterize the image to five or six gray levels as a shading guide.
Wood, size and tools for portraits
Use basswood, birch plywood or another pale, close-grained board, sanded to 220 grit or finer. Visible grain lines fight against skin tone, so avoid pine and oak. A face of about 6 to 8 in tall is a good first size: big enough for detail in the eyes, small enough to finish.
A wire-nib burner is close to essential. You need a spoon or round shader for skin, a small ball or writing tip for the outline and pupils, and a skew or knife tip for hair and eyelashes. Fixed-tip pens are useful here because the tip never shifts. A solid-point craft pen can do a simple pet silhouette, but smooth skin tones are very hard with one. Keep the board flat on the bench and rest the side of your hand on a sheet of paper so skin oils and sweat do not mark the pale areas.
Transfer only the guide lines
Print the grayscale photo at final size and trace a minimal outline: face shape, eye shapes and iris circles, eyebrows, nostrils, the line between the lips, the hairline and the edges of the strongest shadows. Do not trace every wrinkle or strand of hair. Each traced line will show unless it is burned over, and a pale cheek with a dark graphite line on it is hard to fix.
Use wax-free graphite paper with light pressure, or rub pencil on the back of the print. Keep the photo next to you while you burn; you will work from it, not from the transferred lines.
Shade skin in thin layers
Set the burner low, so a slow pass leaves only a pale straw tone on scrap. Start with the eyes, because a likeness depends on them and it is better to fail early. Burn the pupils dark, leave a pure white highlight dot untouched, and shade the iris with fine strokes radiating from the pupil.
Then shade the whole face in its lightest shadow tone using small overlapping circles or short strokes with a shader. Go over the darker areas again and again rather than turning the heat up. Darken in this order: deepest shadows, mid-tones, then soften the transitions. Leave the highlights bare wood. A portrait usually needs four to eight passes in the dark areas, and most of the hours go into this stage.
Hair, fur and finishing details
Burn hair and fur in the direction it grows, using a skew or knife tip with quick flicked strokes that start firm and lift off. Lay down the darkest strands first in the shadowed parts, then lighter strands over the mid-tones, and leave gaps for the shine. On pets, short fur needs short, dense strokes; long fur needs long, curving strokes in groups.
Finish by darkening the pupils, nostrils and the line between the lips once more, which makes the face read from across the room. Rub out graphite with a white eraser. If highlights got too dark, gently scrape them back with a sharp craft knife held almost flat, or use fine sandpaper on a small block. Seal with a non-yellowing water-based finish.
Common portrait problems and fixes
Blotchy skin comes from a tip that is too hot or a stroke that stops in one place; lower the heat and keep the pen moving in circles. Dark start marks on strokes mean the tip touched before moving, so land in motion. A face that looks flat needs darker shadows, not more detail. A likeness that looks off is almost always in the eyes: check spacing and the height of each eye against the photo before shading further.
Carbon build-up on the tip makes tone uneven. Clean the nib every 10 to 15 minutes with a leather strop and polishing compound or very fine abrasive, and the tone will stay consistent.
Frequently asked questions
How long does a wood burned portrait take? A simple 6 in pet portrait takes 4 to 8 hours. A detailed human portrait commonly takes 15 to 40 hours.
Can you wood burn a portrait with a cheap pen? A simple, high-contrast pet portrait yes. Smooth human skin tones need the faster heat recovery and fine control of a wire-nib burner.
What tip is best for portraits? A spoon or round shader for skin, a small ball or writing tip for outlines and pupils, and a skew for hair.
Should I start with a person or a pet? A pet. Fur hides small tone errors and the eyes carry most of the likeness, while human skin shows every blotch.
What you need for this
- See price on AmazonAmazon
YIHUA 939-VI dual pen station, 23 wire nibs
From Best Wire Tip Wood Burners: Pyrography Machines Compared
- See price on AmazonAmazon
MyArtscape wax-free graphite paper, A4, 20 sheets
From Best Graphite and Transfer Paper for Wood Burning Patterns
- See price on AmazonAmazon
BURNMASTER Pyrography Pen, 10 Tips
From Best Pyrography Pens: Replacement and Upgrade Handpieces