# How to Transfer a Pattern or Image to Wood for Wood Burning

Source: https://burnandgrain.com/blog/transfer-image-to-wood-for-burning
Published: 2026-10-01
Publisher: Burn and Grain

**Short answer:** Trace it through graphite paper: tape the print to sanded wood, slide the graphite paper under it dark side down and go over the lines with light pressure. The other three methods are a pencil rub on the back of the print, heat transfer of a laser print with a transfer tip, which comes out mirrored, and a stencil. Leftover lines come off with an eraser or 220 to 320 grit after burning.

You have a printed design and a sanded board, and the design has to get from one to the other without marks that show in the finished piece. The method depends on three things: how much detail the pattern has, whether your pen has a transfer tip, and how dark or rough the wood is. Graphite paper suits most patterns and most pale woods, so its steps are given in full. The table compares it with the three alternatives. Later sections cover the transfer tip, burning over pencil, and what goes wrong on dark or coarse wood.

## Four ways to transfer a pattern to wood for a pyrography pen

All four methods start the same way: wood sanded with the grain to 220 to 320 grit and wiped clean. A smooth surface takes a cleaner line from the paper and from the pen. The table compares what each method needs and where it falls short.

| Method | What you need | Line you get | Cleanup | Where it fails |
| --- | --- | --- | --- | --- |
| Graphite paper tracing | Print, graphite paper, low-tack tape, pencil or stylus | Thin grey line, as exact as your tracing | Eraser or light sanding | Grey lines are hard to see on dark wood |
| Pencil rub on the back | Print and a soft pencil | Fainter, softer line | Eraser | Smudges easily, slow for large designs |
| Heat transfer of a laser print | Laser print or photocopy, transfer tip or flat shader | The whole image at once, mirrored | Sand off what the burn does not cover | Patchy on rough wood, paper scorches if the tip stops |
| Stencil | Stencil, tape, pencil | Repeatable letters and shapes | Eraser | Only the designs the stencil has |

General hobby practice. The heat transfer row follows Weller's project book and Sue Walters' FAQ.

## Graphite paper for wood burning patterns, and why not carbon paper

Graphite paper is a thin sheet coated with graphite on one side. Pressure from a pencil or stylus on top moves a grey line onto the wood. Sue Walters' FAQ calls it far better than carbon paper for pyrography: carbon paper bleeds badly when heated and stains the wood, while graphite can be rubbed out. Weller's project book lists carbon paper for tracing, so this is a point where sources differ. The guide to [transfer paper for wood burning](https://burnandgrain.com/best/best-transfer-paper-for-wood-burning) compares graphite sheets.

The rest of the kit is short: the pattern at its final size, low-tack masking tape, and a pencil or stylus. Walnut Hollow packs graphite transfer paper with its Creative Woodburner wire tool, so check your kit before buying more.

## Steps: transfer a design for a wood burning pen with graphite paper

These steps work for any line pattern on pale wood such as basswood or birch. Trace only the outlines you intend to burn. Shading is done with the pen later and does not need to be drawn on the wood.

1. Sand the wood with the grain to 220 to 320 grit and wipe off all the dust, so the paper lies flat and the lines come out clean.
2. Print or photocopy the pattern at its final size. A copier's reduce and enlarge setting fits a design to the blank.
3. Place the pattern on the wood and fix it with low-tack masking tape along the top edge only, so it lifts like a hinge and drops back in the same place.
4. Lift the pattern and slide 1 sheet of graphite paper under it, dark side down against the wood. Lower the pattern over it.
5. Trace every line once with a pencil or stylus, using light pressure. Use a ruler for straight lines. Pressing hard dents soft wood such as basswood.
6. Before removing the tape, lift the pattern and the graphite paper and check that every line has transferred. Drop them back and trace anything missing.
7. Remove the paper and burn the lines. Then take off any graphite still showing with an eraser or a light pass of 220 to 320 grit sandpaper before sealing.

## How to tell the transfer is ready for the wood burning pen

Check the board before the pen is hot. A good transfer is complete, light and clean. Complete means every line of the pattern is on the wood. Light means a thin grey line you can just follow, not a dark groove. Clean means no grey smudges from a hand resting on the paper. Heavy lines are the ones that cause work later: Sue Walters prefers to sand them lightly or use a white eraser, because wiping graphite off with a damp cloth raises the grain of finely sanded wood.

- Every line present, checked against the pattern before the tape came off.
- No dents that you can feel with a fingertip along a traced line.
- No smudges in areas that will stay unburned. Erase them now, before burning.

## Using a wood burning transfer tip with a laser print

A transfer tip is a flat disc that heats paper instead of marking wood. It moves the toner of a laser print or photocopy onto the board. Weller's project book gives the method for its pattern transfer tip: make a copy with a laser printer, lay it face down on the surface, let the tip heat for about five minutes, then slowly rub the back of the pattern in a circular motion. Sue Walters describes the same result with a household iron on the back of the print.

The image comes out **mirrored**, so flip the design before printing, above all when it includes lettering. Keep the tip moving, because paper scorches where the disc sits still, and lift a corner often to check progress. On a wire-nib burner a flat shader does this job, and Razertip sells a 7 mm transfer and shader tip. Both sources name laser prints and photocopies only. The [tip chart](https://burnandgrain.com/tools/wood-burning-tip-chart) shows the transfer tip and gives medium to high as a general starting heat.

## Can you wood burn over pencil and graphite lines with a pen?

Yes. Pencil lines and graphite paper lines are both graphite, and the standard practice is to burn along them and remove what is left afterward. Erase or lightly sand at 220 to 320 grit once the burning is finished and before any finish goes on, as in [how to seal pyrography](https://burnandgrain.com/blog/how-to-seal-wood-burning). Wood Burn Corner notes that sanding after the burn removes tracing lines, and asks for a very gentle touch at this stage so that light shading is not sanded away with them.

Carbon paper is the exception. Its lines are the ones Sue Walters warns about: they bleed when heated and stain the wood. If a kit or booklet tells you to use carbon paper, swap in graphite paper and follow the same steps.

## Stencils, dark wood and rough wood: where a pyrography transfer fails

A stencil skips paper transfer altogether: tape it down, run a pencil around the openings, lift it and burn the pencil lines. It suits lettering and repeated shapes, and the [stencil guide](https://burnandgrain.com/best/best-wood-burning-stencils) lists metal and adhesive sets.

Dark wood is the common failure. Grey graphite barely shows on walnut, and the burn itself has low contrast there, so pale woods such as basswood, aspen and birch are easier at both stages. Rough wood is the other: a stylus skips across coarse grain and toner transfers in patches. Sanding to 220 to 320 grit before transfer fixes most of it. Pine and oak stay uneven because of their grain and pores. See [best wood for pyrography](https://burnandgrain.com/blog/wood-for-pyrography) for all 12 species.

## Quick answers

Short answers to the searches behind this page. Each follows the steps and sources above, which were read, not tried at a bench.

- **Is graphite paper for wood burning the same as carbon paper?** No. Graphite paper erases. Carbon paper bleeds when heated and stains the wood, according to Sue Walters.
- **What does a wood burning transfer tip do?** It heats the back of a laser print or photocopy so the toner moves onto the wood. The image comes out mirrored.
- **Can you wood burn over pencil?** Yes. Burn along the line, then erase or sand off what still shows at 220 to 320 grit.
- **Where do pyrography designs to trace come from?** Any simple line art works. Weller's project book suggests coloring books, sized on a copier.
- **Does pyrography transfer paper work on dark wood?** Poorly. Grey lines are hard to see on walnut, so pale wood is the easier choice.

## Gear guides for this topic

- https://burnandgrain.com/best/best-transfer-paper-for-wood-burning
- https://burnandgrain.com/best/best-wood-burning-stencils
- https://burnandgrain.com/best/best-wood-burning-tips-set
- https://burnandgrain.com/best/best-wood-blanks-for-pyrography

## Sources

- [Sue Walters: General Burning FAQ](https://suewalters.com/pages/general-faq)
- [Weller: WSB25WB Woodburning Kit project book](https://res.cloudinary.com/iwh/image/upload/q_auto,g_center/assets/1/26/Documents/Weller/WSB25WB/wsb25wb_doc_4.pdf)
- [Wood Burn Corner: Sanding Your Wood Before and After You Burn](https://www.woodburncorner.com/burnblog/sanding-your-wood-before-and-after-you-burn)
