# Can You Use a Wood Burning Pen on Leather? Types, Heat and Technique

Source: https://burnandgrain.com/blog/can-you-wood-burn-leather
Published: 2026-10-01
Publisher: Burn and Grain

**Short answer:** Yes, but only on vegetable-tanned leather. The pyrography teacher Sue Walters says not to burn chromium-tanned leather, and faux leather is plastic, which melts and gives off fumes. Leather needs only gentle heat: Walnut Hollow lists it in the two lowest of the four zones on its dial. No verified leather temperature exists, so set the heat on a scrap.

The pen you use on wood is the same pen you use on leather. What changes is the material and the heat. Leather is a hide preserved by tanning, and the tanning method decides whether sources say to burn it at all. Most leather made today is chrome-tanned, so the belt, bag or offcut you already own is more likely chrome-tanned than not. This page covers which leather the sources name, how low to set the pen, how to move it and which tips suit the job. Heat is given as dial positions, not degrees.

## Which leather can you burn with a wood burning pen?

Go by the tanning method, as the label or the seller states it. If a piece of leather is not identified as vegetable-tanned, treat it as chrome-tanned and do not burn it.

| Material | Burn it? | What the sources say |
| --- | --- | --- |
| Vegetable-tanned leather, bare | Yes | The only leather Sue Walters's burning FAQ names for pyrography |
| Chrome-tanned (chromium-tanned) leather | No | Sue Walters: do not burn on chromium-tanned leather |
| Faux leather, vinyl, PU | No | It is plastic: it melts and gives off fumes |
| Dyed, painted or sealed leather | No | Burn only bare, untreated material |
| Leather of unknown tanning | No | Most modern leather is chrome-tanned, so assume it is |

Compiled from Sue Walters's General Burning FAQ and standard pyrography safety rules. Not a test.

## What sources say about chrome-tanned leather and pyrography

Chrome tanning uses chromium salts, where vegetable tanning uses tannins from bark and leaves. Sue Walters's FAQ states the rule in one line: do not burn on chromium-tanned leather, only on vegetable-tanned. The page gives the instruction without a reason, and this site adds none of its own. It is a warning from a named source, and this page treats it as a hard no.

None of this means that smoke from vegetable-tanned leather is harmless. No source read for this page says so, and neither does this page. Vegetable-tanned is the type the sources name for burning. The ventilation rules further down apply to every piece.

## Can you use a wood burning tool on faux leather?

No, not to draw a design. Faux leather, vinyl and PU are plastic, and plastic under a hot tip melts and gives off fumes. The standard rule for plastics is to ventilate and to cut on glass or tile, which is advice for cutting with a hot knife, not for pyrography. If a product is described as vegan leather, PU leather or leatherette, do not burn it.

## Leather pyrography temperature: the lowest zones on the dial

There is no verified temperature for leather. Hobby sources disagree by several hundred degrees, and craft pens are not calibrated, so a single number would be false precision. What makers and teachers do publish is the direction: low. Sue Walters writes that leather needs only a gentle heat. Walnut Hollow's Versa-Tool instructions list leather in **zones 1 and 2 of 4**, the two lowest. Wood first appears in zone 2.

On a solid pen with a dial, start in the lowest zone and let the pen heat for 4 to 5 minutes after each change. On a wire-nib burner, dial numbers are not degrees and differ by unit, so start at the bottom and go up one step at a time. A one-heat solid pen cannot be turned down. Makers list those pens at about 900 to 950 F, the high band for wood, so a pen with a dial is the fitting tool for leather. The [wood burning temperature chart](https://burnandgrain.com/tools/wood-burning-temperature-chart) carries leather as its own row.

Note: Zones are not degrees, and leather varies from hide to hide. Repeat the scrap test for every new piece of leather.

## Technique: light, fast strokes with the pen on leather

The rule from wood applies with more force: light pressure, and the longer the tip stays in one place, the darker the burn. On leather, work in light, fast strokes and build the tone in passes.

1. Cut an offcut from the same piece of leather, or use an edge that will be trimmed off. This is the scrap for every heat change.
2. Set the dial to its lowest zone and let a solid pen heat for 4 to 5 minutes. A wire nib heats quickly: start at the bottom of the dial.
3. Draw a row of straight strokes on the scrap at a steady speed with light pressure. If no mark appears, raise the heat one small step and repeat.
4. Stop at the first setting that leaves an even brown line. If the line is black or the tip sinks into the surface, go back one step.
5. Mark the design lightly, then burn the outlines with quick single strokes. Lift the tip at the end of each stroke and do not pause on the leather.
6. Shade last, in several light passes, at the same setting or lower. Let the pen cool on its stand before you change a solid tip.

## Which wood burning tips work on leather?

No maker's instructions read for this page name a tip for leather. The shapes do the same jobs as on wood, so choose by the mark you want. A rounded tip makes an even line in any direction, which suits writing and outlines. A shader, used with a very light touch, lays down tone. A skew or knife tip cuts slightly into the surface, so keep it for crisp straight lines.

On a wire-nib burner a fine nib runs hotter than a heavy shader at the same dial number. Turn down when you switch to a finer nib. The [wood burning tip chart](https://burnandgrain.com/tools/wood-burning-tip-chart) shows every shape.

| Job | Solid tip | Wire nib |
| --- | --- | --- |
| Writing and outlines | Flow, mini flow | Writing nib, ball stylus |
| Fine detail and dots | Cone, mini flow | Ball stylus, writing nib |
| Shading | Shading tip | Spoon shader, spear shader |
| Names without freehand | Letter and number stamps | None |

Tip shapes by job, from this site's tip chart. A general guide: no maker lists tips for leather.

## Ventilation when you burn leather with a pyrography pen

Burning leather makes smoke. Burn only bare, untreated material, with ventilation: an open window and a fan or extractor that pulls smoke away from your face without blowing on the tip. A dust mask is for sanding dust. It does not filter smoke or gases. For the full picture, see [is pyrography safe](https://burnandgrain.com/blog/is-pyrography-safe) and the [smoke extractor guide](https://burnandgrain.com/best/best-pyrography-smoke-extractor).

The tip and barrel cause burns. Use the stand, let the pen cool before changing tips, and keep children and pets away. Leather pieces are often small, so hold the piece well behind the tip.

## Quick answers

Short answers on leather. Heat is given as dial positions, because no verified leather temperature exists. Test on an offcut first.

- **Can you use a wood burning pen on leather?** Yes, on bare vegetable-tanned leather only, at the lowest heat the pen offers.
- **What is the leather pyrography temperature?** No verified figure exists. Walnut Hollow lists leather in zones 1 and 2 of 4 on its dial.
- **Can you use a wood burning tool on faux leather?** No. It is plastic, which melts and gives off fumes.
- **Do you need a special pyrography pen for leather?** No. The same pen works, but it needs a dial: a one-heat pen cannot be turned down.
- **Can you burn chrome-tanned leather?** No. Sue Walters's burning FAQ says not to burn on chromium-tanned leather.

## Gear guides for this topic

- https://burnandgrain.com/best/best-wood-burning-tool-with-temperature-control
- https://burnandgrain.com/best/best-wire-tip-wood-burner
- https://burnandgrain.com/best/best-wood-burning-tips-set
- https://burnandgrain.com/best/best-pyrography-smoke-extractor

## Sources

- [Sue Walters: General Burning FAQ](https://suewalters.com/pages/general-faq)
- [Walnut Hollow: Creative Versa-Tool instructions 38283-I](https://news.lincc.org/sites/default/files/lot-manuals/wood%20burning%20tool%20instructions.pdf)
- [Wikipedia: Tanning (leather)](https://en.wikipedia.org/wiki/Tanning_(leather))
